Heavy-Duty & Automotive Machining Done Right on Main Street
In modern automotive maintenance, many chain stores have completely eliminated machine shop capabilities, forcing car owners and technicians to discard salvageable metal and purchase costly complete assemblies. At Rieth Auto Stores, we believe in true craftsmanship, technical precision, and economical alternatives. Our in-house machine shop at 1806 East Main St in Mesa, AZ has serviced thousands of cylinder heads, engine blocks, brake rotors, and flywheels for over three decades.
Whether you are rebuilding a classic Chevrolet small block, refreshing a daily commuter Honda cylinder head after an overheating event, or resurfacing industrial brake drums for a commercial vehicle, our equipment and machinists adhere to stringent micrometer tolerances.
Our Primary Machine Shop Capabilities
Brake Drum & Rotor Resurfacing
Modern vehicle rotors are manufactured with minimal thickness to reduce unsprung vehicle weight. Over time, braking heat cycles induce disc thickness variation (DTV), surface grooving, and pedal shudder. Resurfacing cleans rotor faces, restores parallel surfaces, and eliminates shudder when adequate metal thickness remains above the manufacturer's discard minimum (Discard Min).
Turnaround: Same-day or while you wait on standard automotive rotors.
Cylinder Head Resurfacing (Head Shaving)
Arizona summer temperatures routinely exceed 110°F, placing extreme thermal stress on vehicle cooling systems. When an engine overheats, the aluminum or cast-iron cylinder head frequently warps, causing head gasket failure, coolant consumption, or oil contamination. We mill the head to precise Ra micro-inch surface finish specifications necessary for modern Multi-Layer Steel (MLS) gaskets.
Turnaround: Typically 24 hours depending on valve work requirements.
Engine Block Cylinder Boring & Honing
When cylinder walls suffer scoring, taper, or out-of-round wear, boring the cylinders to an exact oversize (e.g. +.020", +.030") followed by plateau honing restores factory compression, ensures proper piston ring seal, and eliminates oil burning. This is an economical, reliable alternative to buying a crate engine.
Capabilities: Domestic V8/V6, import inline-4/inline-6, and light commercial diesels.
Flywheel Grinding & Step Resurfacing
Whenever you replace a manual clutch kit, installing new friction discs against a heat-checked or grooved flywheel causes clutch chatter and premature failure. We grind flat and stepped flywheels to exact OEM depth specifications, creating an ideal cross-hatch mating surface for smooth clutch engagement.
Compatibility: Passenger cars, muscle cars, light trucks, and heavy-duty pickups.
Hydraulic Hose Fabrication & Mechanical Press Work
In addition to traditional cutting and surfacing operations, our shop provides high-demand specialized mechanical fabrication:
| Service Category | Equipment & Capabilities | Common Applications |
|---|---|---|
| Custom Hydraulic Hoses | High-tonnage hydraulic crimping press with broad assortment of Gates, Carquest, and Parker fittings (JIC, NPT, ORFS, metric). | Heavy equipment, power steering assemblies, tractor hydraulics, industrial lifts, commercial A/C lines. |
| Wheel Bearing & Hub Pressing | Hydraulic bench presses for safe bearing removal and installation without damaging steering knuckles or hubs. | Press-in front wheel bearings, hub assemblies, ABS tone rings, axle shaft bearings. |
| U-Joint & Axle Services | Universal joint pressing, pinion yoke servicing, and driveshaft component replacement. | 4x4 trucks, rear-wheel-drive fleet vans, commercial box trucks. |
| Control Arm Bushing Pressing | Specialized arbor adapters for extracting rusted or vulcanized rubber/polyurethane suspension bushings. | Front lower control arms, trailing arms, leaf spring eyelet bushings. |
Machining Tolerances & Quality Assurance
Every piece of metal that enters our machine shop is subjected to rigorous quality control checks before leaving our facility:
- Rotor Micrometer Inspection: Rotors are measured with calibrated digital micrometers across multiple points to verify minimum thickness safety limits before machining begins.
- Precision Straight-Edge & Feeler Gauges: Cylinder heads and engine decks are checked across both diagonals to determine exact warpage down to 0.001".
- Surface Roughness (Ra) Adherence: MLS head gaskets require surface finishes typically under 30 Ra to guarantee micro-sealing; our diamond tooling leaves a mirror-smooth finish.
- Plateau Honing: Cross-hatch angles are held between 45° and 60° to retain boundary lubrication oil for the piston rings during engine break-in.
Save Money on Brake Service
Replacing four high-performance truck or SUV rotors can easily cost $400 or more. Resurfacing verified good rotors at Rieth Auto typically costs a fraction of that price, giving you smooth, quiet braking performance without unnecessary waste.
Machine Shop Frequently Asked Questions
How do I know if my brake rotors can be resurfaced or need replacement?
Every brake rotor has a stamped "Minimum Thickness" or "Discard" measurement cast into the rotor hat or edge. Bring your rotors to our counter at 1806 E Main St. Our technicians will measure them with a micrometer. If the metal has enough thickness remaining after accounting for the cut depth, we can safely resurface them. If they are below safety minimums or have deep structural cracks, we stock new replacement rotors immediately.
Do I need to disassemble the cylinder head before bringing it to your shop?
While stripping the head of manifolds, spark plugs, sensors, and camshafts makes the process faster and more economical, we can handle valve disassembly, cleaning, and pressure testing if requested. Call us at (480) 962-4211 to discuss your specific head.
Can you duplicate an existing broken hydraulic hose?
Yes. Bring your old, leaking, or damaged hydraulic line to our counter. We will match the internal diameter, pressure rating, fitting thread pitch, and orientation angle, and crimp a brand-new high-pressure hose while you wait.
What is the typical turnaround time for machine shop services?
Brake rotors, drums, and hydraulic hoses are frequently completed same-day or while you wait. Flywheels, bearing presses, and cylinder head resurfacing are typically completed within 24 to 48 hours depending on job complexity.